Tanaka

– 4.5mm aluminum rod

– Aluminum bolts

– Made in Japan

– 44 grams

– Premium finishes: copper, chrome-plate and Neo Black

Designed to hold snugly 3.5” diameter bottles such as the Nalgene 32 oz. wide mouth

• Tubular stainless steel construction

• Two different mounting positions

• Fits bottles 3.5” in diameter and 17.5” tall at the “shoulder”

• Made in Japan

Stainless steel wire basket great for mounting to a front or rear rack. 15" x 10" x 4-3/4

Natural stainless steel or Black

Stainless steel wire basket great for mounting to a front or rear rack. Low profile for lighter weight and less likely to cause interference with lower set handlebars.
15" x 10" x 2-3/8"

Natural stainless steel or Black finish.
With limited edition painted colours.

Stainless steel bottle cage made with extra stiff 6mm OD tubing.
– Three sets of holes for multi-position mounting
– Weight: 83g
– Semi-polish finish
– Made in Japan

5mm tubular stainless steel cage.

This unique rack is designed specifically for wire baskets that don't come with their own mounting hardware. The T-shaped platform may prevent the basket from bending or warping that can sometimes happen to well-used baskets zip-tied to narrow front racks.

The basket (not included) lays on a flat steel plate and bolted securely at three points. 
The platform attaches to the front fork much like other front racks – a tongue extends to the fork crown and two solid struts connect to the fork. If used on a road or CX fork, the struts would connect to the pannier eyelets or the fender eyelets. (Mini-rack mounts might be too high to offer optimum support.) 

– Platform size: 260mm wide x 140mm deep x 30mm deep
– The struts have a lot more width adjustment than on a regular rack, so you can fit roads forks or MTB forks as wide as 160mm. 
– Struts are 390mm long and can be cut down to suit different forks

Sturdy steel rear rack that comes in 7 colors like Tanaka Eight Moves bottle cages.
It mounts slightly offset to the rear of the bike, to reduce incidence of heel clipping with panniers for folks with large feet, large panniers or with bikes with short chainstays.

– Tubular steel construction

– Rear offset design for heel clearance with pannier; better clearance with saddle and seatpost

– Requires only one wrench size to install

– 7 powder coated colors

– Fits 700c wheel bikes and some 29ers (fits smaller wheel bikes, too.

– Width 180 mm × Depth 350 mm × Height 410 mm

– Max. load: 40 lbs (18kg)

– Made in Japan

A side loading bottle cage allows easier bottle removal and loading on smaller frames and in tight spaces (such as if a frame bag is in use.) Instead of pulling the bottle straight up and out, you pull it to the right or left. 

– Duraluminum construction
– The Eight Moves design has eight mounting slots to allows to be adjusted up and down to make room for another cage or a frame bag, etc. Almost 70mm of adjustment.
– Seven colors
– Bolts not included
– Made in Japan

The "Left" side cage has its opening on the left side when installed on the donwntube. When installed on the seat tube, the opening flips to the right side. If you are getting bottles for both the seat tube and down tube AND want the opening to be on the same sides, get a Right and Left Side Cage.

A side loading bottle cage allows easier bottle removal and loading on smaller frames and in tight spaces (such as if a frame bag is in use.) Instead of pulling the bottle straight up and out, you pull it to the right or left. 

– Duraluminum construction
– The Eight Moves design has eight mounting slots to allows to be adjusted up and down to make room for another cage or a frame bag, etc. Almost 70mm of adjustment.
– Seven colors
– Bolts not included
– Made in Japan

The "Left" side cage has its opening on the left side when installed on the donwntube. When installed on the seat tube, the opening flips to the right side. If you are getting bottles for both the seat tube and down tube AND want the opening to be on the same sides, get a Right and Left Side Cage.